24/7 BUSINESS EMERGENCY SERVICE - Call Us Now (616) 350-9175

Understanding HVAC Load Calculations in Industrial Buildings

Understanding HVAC Load Calculations in Industrial Buildings

An HVAC load calculation tells you how much heating and cooling a building needs at its design conditions. In an industrial building, that number depends on far more than floor area. Process equipment, ventilation, door traffic and the building envelope all add to it, and each one can change over the life of the facility.

When the calculation is wrong, the error carries into every decision that follows: equipment size, duct design, controls and operating cost.

What Is an HVAC Load Calculation?

A load calculation is an engineering estimate of the heat a building gains in summer and loses in winter. The result, in Btu per hour or tons, sets the capacity the HVAC system has to deliver on the hottest and coldest days the design expects.

For commercial and industrial buildings, the common references are ACCA Manual N and the ASHRAE load calculation methods. Both work from the same idea: add up every source of heat gain and heat loss, room by room or zone by zone, instead of estimating from square footage.

What Goes Into the Calculation

In a manufacturing plant or warehouse, the main inputs are:

  • Building envelope: wall and roof construction, insulation, windows and skylights
  • Local design temperatures for the site, not an average day
  • Outdoor air required for ventilation and exhaust makeup
  • Infiltration through dock doors, overhead doors and leaks in the envelope
  • Internal heat from process equipment, motors, compressors and lighting
  • People, shifts and hours of operation
  • Zones with different needs, such as offices, production floors and storage

Process loads and ventilation are often the largest items in an industrial building. A plant that adds a production line or an exhaust hood changes its load even if the building itself stays the same.

Why Rules of Thumb Mis-Size Industrial Systems

Sizing by square feet per ton is fast, and it is still common in retrofits. It assumes an average building. Industrial buildings are rarely average. A warehouse with high ceilings and few people needs a different system from a machining area of the same size.

The result is equipment that is too large or too small:

  • Oversized systems short cycle. They reach the thermostat setting quickly, shut off, and start again. The space dehumidifies poorly, temperatures swing, and starts and stops add wear to compressors and contactors.
  • Undersized systems run without a break on design days and still fall behind. Parts wear faster, and the space drifts out of range when production needs it most.

Sizing errors are one of the failure drivers we covered in why commercial HVAC systems fail in Michigan facilities. Many repeat repairs start with a system that never matched its load.

Michigan Conditions Change the Numbers

West Michigan buildings have to handle cold winter design days and humid summer days in the same year. Heating loads, freeze protection for outdoor air, and summer humidity all have to be in the calculation. A system that only meets the cooling load can still struggle in January if ventilation air is not preheated or tempered.

When to Ask for a New Load Calculation

A new calculation is worth the time when:

  • You plan to replace rooftop units, air handlers or a heating plant
  • Production equipment, shifts or occupancy have changed
  • Part of the building changed use, for example storage to production
  • Some areas run hot or cold while others are fine
  • Equipment short cycles or runs constantly
  • You add insulation, new windows or a new roof

Replacing old equipment with the same size is a common mistake. The original unit may have been sized for a building that no longer exists.

What the Calculation Leads To

A good load calculation starts the design. It sets equipment selection, airflow, duct sizing and zoning. It also gives the controls a realistic range to work in. Learn more about our HVAC load calculation services.

Accurate sizing also makes maintenance easier to plan, because equipment that runs within its design range is simpler to keep in condition. For seasonal checks, see our fall HVAC maintenance tips.

Do the Load Calculation Before You Choose Equipment

For an industrial building, the load calculation decides how well every other part of the HVAC system can perform. It is worth doing before a replacement, after a change in how the building is used, and any time comfort or process temperatures become hard to hold.

If you are planning HVAC work at a Grand Rapids or West Michigan facility, contact RMS Pros to talk through a load calculation before you choose equipment.

Share this Post

Rheem HVAC and Refrigeration Supplier in West Michigan - RMS Pros Partner
IIAR Industrial Refrigeration Partner in West Michigan - RMS Pros Supplier
Trane Commercial HVAC Solutions in West Michigan - RMS Pros Partner
Bohn Commercial Refrigeration Equipment Supplier in West Michigan - RMS Pros Partner
Arneg Commercial Refrigeration Supplier in West Michigan - RMS Pros Partner
Carrier HVAC Systems and Solutions Supplier in West Michigan - RMS Pros Partner
Dectron Indoor Pool and Humidity Control Supplier in West Michigan - RMS Pros Partner
True Commercial Refrigeration Supplier in West Michigan - RMS Pros Partner
Krack Commercial Refrigeration Equipment Supplier in West Michigan - RMS Pros Partner
Heatcraft Refrigeration Solutions Supplier in West Michigan - RMS Pros Partner
Delfield Foodservice Equipment Supplier in West Michigan - RMS Pros Partner
Beverage-Air Commercial Refrigeration Supplier in West Michigan - RMS Pros Partner
Manitowoc Ice Machines Supplier in West Michigan - RMS Pros Partner
Scotsman Ice Machines Supplier in West Michigan - RMS Pros Partner
Keeprite HVAC and Refrigeration Systems Supplier in West Michigan - RMS Pros Partner
Russell Refrigeration Equipment Supplier in West Michigan - RMS Pros Partner
McQuay HVAC Equipment Supplier in West Michigan - RMS Pros Partner
Vilter Industrial Refrigeration Supplier in West Michigan - RMS Pros Partner
Baltimore Aircoil (BAC) Cooling Towers Supplier in West Michigan - RMS Pros Partner
EvapCo Industrial Cooling Towers Supplier in West Michigan - RMS Pros Partner
Frick Industrial Refrigeration Systems Supplier in West Michigan - RMS Pros Partner
GEA Refrigeration Systems Supplier in West Michigan - RMS Pros Partner
MYCOM Industrial Refrigeration Supplier in West Michigan - RMS Pros Partner
York Commercial HVAC Supplier in West Michigan - RMS Pros Partner
US Cooler Commercial Walk-In Coolers Supplier in West Michigan - RMS Pros Partner
Tonka HVAC and Air Purification Supplier in West Michigan - RMS Pros Partner
Kramer Commercial Refrigeration Supplier in West Michigan - RMS Pros Partner
Goodman HVAC Systems Supplier in West Michigan - RMS Pros Partner
Bryant HVAC Solutions Supplier in West Michigan - RMS Pros Partner
American Standard Commercial HVAC Supplier in West Michigan - RMS Pros Partner
Rheem HVAC and Refrigeration Supplier in West Michigan - RMS Pros Partner
Air King Ventilation Products Supplier in West Michigan - RMS Pros Partner
AbsolutAire Commercial HVAC Supplier in West Michigan - RMS Pros Partner
Cleaver-Brooks Boiler Systems Supplier in West Michigan - RMS Pros Partner
Weil-McLain Commercial Boilers Supplier in West Michigan - RMS Pros Partner
Raypak Commercial Water Heating Systems Supplier in West Michigan - RMS Pros Partner